Unfortunately, just like most appliances, it’s not immune to malfunctions. Users have complained that their Stanley Fatmax Powerit 1000a turns on itself, doesn’t turn on, keeps beeping, and has many more problems.

The issues are inconveniencing and challenging, especially when they happen unexpectedly and you don’t know the cause of the problem or how to fix it. With the Stanley Fatmax Powerit 1000a troubleshooting tips below, you will not only identify the problems but also fix them.

Common Fatmax Powerit 1000a problems and their fix

These are the most common issues you will experience while using the Powerit 1000a.

The Stanley Fatmax Powerit 1000a won’t turn on

When your Fatmax Powerit 1000a doesn’t turn on, it could be because of issues like dead batteries and lack of charge or complex internal damage to essential components.

To fix this, try the following solutions:

• Check the batteries: Even though it has a huge battery capacity that can’t be depleted easily, you should check to be sure. In fact, to avoid surprises, charge your Fatmax Powerit 1000a at least once per month or whenever the charge runs low. Also, charging helps to maintain the battery life. If the batteries are faulty, you should replace them with new ones immediately.
• Run a power cycle: Power cycling the Fatmax Powerit 1000a helps correct minor system glitches affecting performance. It’s as simple as turning off the device and then waiting a few seconds before switching it back on.
• Turn off the compressor switch: While jump-starting your car or charging other electrical appliances, ensure the compressor switch is off to avoid interference.

READ: How to troubleshoot the Pentair Mastertemp 400

Stanley Fatmax Powerit 1000a keeps beeping

The Stanley Fatmax Powerit 1000a has an in-built safety system that sounds an alarm whenever there’s an incorrect connection. Therefore, to stop the beeping sound from your device, check your clamps connection and correct it.

Also, if you’re running low on oil or used unfiltered or the wrong oil, the Fatmax Powerit 1000a will beep consistently. You’ll have to refill the oil or change it entirely to prevent irreversible damage to parts like the piston, valve, and jack.

Stanley Fatmax Powerit 1000a doesn’t keep charge

If you notice your Fatmax Powerit 1000a drains its battery fast, you may have been leaving it On after use. This forces you to charge it more frequently than necessary. So, to avoid that, ensure it’s switched off after use and stored in a safe place under room temperature.

The LED indicators don’t illuminate

If you pressed the battery status button, but the battery status indication didn’t show, your battery might be completely depleted. You should recharge it, then press and hold the status button again for a few seconds.

The compressor will not inflate

When your compressor fails to inflate, you should try the following:

• Ensure the compressor is turned On.
• Confirm if the Fatmax Powerit 1000a is charged.
• Ensure the nozzle is attached firmly to the tires. If it’s damaged, replace it immediately.
• Press the On/Off button to switch the compressor Off and let it cool for at least 10 minutes, then try to inflate your inflatables.

The USB port doesn’t power the appliance

Check if the USB power button is turned on to troubleshoot USB issues. Next, confirm your Fatmax Powerit 1000a charge. Lastly, check the USB port for damages.

Stanley Fatmax Powerit 1000a is not charging

Charging issues are mainly caused by a faulty charging cord, power outlet, or battery. So, to be sure, try a different cord, connect to another power outlet, or replace the batteries.

READ: The best generator for RV air conditioner

The Fatmax machine starts the stops

When you encounter this problem, you may be using the machine aggressively, running low on water or oil, the valve is damaged, or there’re other internal motor issues. To solve the issue, let the machine rest after continuous usage and don’t overload it. Also, refill the oil and water levels, and replace damaged parts.

Fatmax Powerit 1000a emits cold or hot air

The temperature of the air coming from the compressor should be balanced. Mismatched air temperatures could damage the air calve, air tank, and pipe. The problem is caused by the accumulation of dirt in the compressor, over or under the compressor, and using the compressor for long without a break.

You can avoid these issues when you let the machine rest and check and repair or replace worn-out parts.

Air pressure and flow problems

Low or high air pressure and flow also significantly impact your Fatmax compressor’s performance. The source of the problem could be a faulty piston, valve, gasket, power switch, air filters, fuse, jack, or even power supply.

Check each of them and replace those that are completely worn out. Next, reset the Stanley Fatmax Powerit 1000a and check if the air pressure and flow are balanced.

How long does Stanley Fatmax last?

After the initial charge when you purchase the Stanley Fatmax Powerit 1000a, it can retain the charge for up to 12 months if it’s not in use. However, the charge can only last 1 hour on the highest setting and 7 hours on the lowest setting.

How long does it take to charge a Stanley Fatmax Powerit 1000a?

The time taken to charge your Fatmax to full capacity depends on its discharge level. It’ll need 12-14 hours to recharge if it’s completely discharged. You will know it has finished charging when the LED indicator illuminates, and the green LED light flashes

That wraps up our Stanley Fatmax Powerit 1000a troubleshooting guide. Hopefully, one of the solutions helped you correct a recurring problem, and your machine now works efficiently. You can avoid future problems by simply reading the manufacturer’s user guide and following all the recommendations.

If nothing works, get in touch with the Stanley support team and inform them of your predicament. They’re better placed to understand the problem, diagnose it, and provide the right solution. Also, you should know that they have great warranty policies that will help you save a lot on repair expenses.

READ: How to choose the right cordless screwdriver

The post Stanley Fatmax Powerit 1000a troubleshooting guide appeared first on Home Gadgets.

Hand warmers are being adopted fast because they have adjustable settings and can be recharged and reused when the battery depletes. But before you consider these benefits, it is important to ensure your safety and that of your family by ensuring that these warmers are safe.

What are hand warmers?

They are small packets used to keep hands warm in cold conditions. You can use them during outdoor activities such as camping or place them inside your socks or sleeping bag to keep warm.

There are different types of hand warmers, such as the chemical hand warmer, lighter-fueled hand warmers, and battery-operated hand warmers. The chemical and lighter-fueled hand warmers are used only once while the rechargeable hand warmers can be reused.

READ: Best king-size electric blankets with controllers

Are electric hand warmers safe?

Electric hand warmers are safe when used properly. They may be uncomfortable for first-time users because their skin has not yet adjusted to the temperature. 

Children, however, are known to have sensitive skin. Their skin should, therefore, not make direct contact with the hand warmers. 

You should also make sure that you are not using hand warmers while they are charging to avoid injury. 

Note that there are other types of hand warmer such as the catalytic burner warmer, that pose to be dangerous. To prevent any dangers or mishaps, ensure that there is enough fuel in the pocket and there is no excess fuel leakage before lighting it up.

These hand warmers are also prone to carbon monoxide leakage if not sealed properly. To avoid this, you can use an insulated sleeve when holding warmers that use catalytic burners.

Can rechargeable hand warmers explode?

In normal situations, rechargeable hand warmers do not explode. They can, however, explode if they are close to resistors and flammable materials or when they get short-circuited. 

A faulty battery can also cause lithium hand warmers to explode. You should, therefore, invest in quality hand warmers that come with a good-conditioned battery.

Can a hand warmer start a fire?

No, hand warmers cannot start a fire when properly used. However, there are cases where using liquid fuel hand warmers may start a fire. It may occur due to liquid fuel leakage because of pouring too much fuel than what is required or using the wrong fuel.

You should also keep it away from flammable materials such as clothes and quilts. Lithium batteries are prone to spontaneous combustion. 

You should also properly dispose of the hand warmers because it contains iron powder, vermiculite, salt, and activated charcoal. When exposed to fire, they produce intoxicating fumes that may affect your lungs and gastrointestinal system.

READ: Best water boiler and warmers to buy

Are hand warmers harmful?

No, they are not. As long as you do not ingest the contents, then you are just fine. 

Hand warmers contain an iron powder that, when consumed, can be harmful to your health. It may lead to stomach bleeding, diarrhea and vomiting. 

While hand warmers from the best brands are generally safe, make sure they are not directly contacting your skin to prevent burns. 

Are lithium hand warmers safe?

Although they are mostly safe, lithium hand warmers can prove to be dangerous when improperly used. When there is a defect in the protection case and the battery, it is likely to start a fire.

It may also occur when there are abnormal temperatures, or there is a short circuit overcharge. 

To ensure that you are purchasing a safe product for yourself or your loved ones, follow the following tips:

• Ensure that the hand warmer has a product manual, certificate, warranty card, and necessary accessories. 
• When purchasing a hand warmer, check its production date which should be within a year. If it is more than a year, the battery capacity is reduced and therefore affects the product in general.
• Purchase hand warmers from big or renowned brands such as Ocoopa, Zippo, and Hot Hands hand warmers.
• Do not use hand warmers for a long time to prevent burns on your skin. You should also not use it in the same area repeatedly as it may burn your skin. 

Rechargeable hand warmers are safe and ideal for use during cold weather. However, you have to ensure that you follow the recommended safety instructions to avoid injuries.

The post Are rechargeable hand warmers safe? appeared first on Home Gadgets.

If you’re planning to install misters on their lawn, you have to consider the distance between the misting nozzles for the entire system to be effective. 

So, how far apart should misting nozzles be when setting up a misting system? In this article, we will not only cover the distance between nozzles but also explain how to position the mist line and other factors to consider during installation.

How far apart should misting nozzles be placed?

The correct spacing for misting nozzles is 3 – 5 feet apart in all directions. With the correct positioning, all your guests will be showered with a cool and refreshing mist during the hot summer months.

There is also no limit to the number of heads you can install. You can install as many as 20 heads on your misting system. 

How to install a misting system

Most of the misting systems are DIY and are, therefore, easy to install. They are mostly used during the hot season when evaporative cooling works best. 

Below are the steps to setting up a misting system:

• Screw the clamps into the marked areas and measure to confirm they are at the correct distances. 
• Ensure that the tubing sections are also correctly joined with the high-pressure compression fittings.
• Choose a pump that is compatible with your current power source for the misting system. Remember to choose one that has high pressure of at least 1000 psi and has a pump cover.
• Once the pump is connected to the power source and water, you can assemble the misting components. Ensure that the misting lines are burrowed at a proper depth to prevent tripping over them. 
• When the misting system is complete, run water for thirty seconds to clean air and dirt off the mist lines. 
• You also check the tubing to ensure there are no leaks where the compression fittings are installed.
• Install the misting nozzles high enough, at least 8 feet and above. They should be placed differently and at different heights. While fixing them, ensure that they do not drip water.

Here’s a video detailing the entire process.

Read Also: List of the best personal misters

If you feel that the process is difficult and time-consuming for you, you can hire a professional service to help you install the misting system. They will ensure that the mist evaporation covers the whole area and is comfortable for everyone.

Where should I position a mist line?

They should be installed on the structure’s exterior because most misting systems are installed once the structure is completely built.

You should also ensure that it is fixed at a proper height and where there is good airflow.

How high should the misters be?

The mist lines should be placed at or above eight feet to ensure that the patio and the people are not wet.

When installed too high, however, they may generate a pleading and misty effect but do not cool the space.

Read Also: How much water does a misting system use per hour?

The post How far apart should misting nozzles be? appeared first on Home Gadgets.

Well, the short answer is yes, they do. But, if we left it at that, you’d be left with more questions like, “how?” and “at what humidity do misters work?” So, to avoid all that, we’ll dive into the long answer. First, let’s look at how the systems work.

Read: Best way to increase humidity in an air-conditioned room

How do misting systems work?

Misting systems work by pumping fine water droplets out of tiny nozzles and spraying them into the air. Next, the cooling effect is achieved through three main methods:

• Conduction from the body to the cool air around.
• Convection breeze coming from the mister’s fan.
• Evaporation of the water droplets to cool the air.

Out of the three, evaporative cooling is the most significant. It works by using the heat energy in the environment to evaporate the water droplets being released.

As a result, you’re left with cooler air. The finer the water droplets or mist the better the results because they evaporate faster. Plus, you won’t have to worry about getting wet.

Now, to get those tiny droplets, you should make sure you get high-pressure misting systems (above 250 psi/17 bar) with tiny nozzles.

Read Also: Do I need a pump for a misting system?

Are misters good in humid weather?

Having seen that misters work well through evaporative cooling, which is efficient in hot and dry climates, it can be challenging to maintain the same level of performance in humid environments.

To start with, the evaporation wouldn’t be as fast since a good percentage of the space in the air is already filled with humidity. Secondly, you can only add so much mist into the humid air before it gets saturated.

So, how do you use misting systems to cool humid air?

• First, make sure the nozzles are as tiny as possible then go for a high-pressure mister (1000 psi). This is to make sure the water droplets are extremely micro so that they can evaporate faster and cool the area—while avoiding saturation.
• You must have the misting fan to help blow the evaporated air away to go and cool a wider area while leaving room for other droplets to evaporate.

NOTE: Evaporative cooling will only work in humid environments when the humidity is less than 100%

• Between 80% – 100% humidity, you can only get a maximum of 10 degrees Fahrenheit of cooling with systems.
• Between 40% -80% humidity, you can get up to 20 degrees Fahrenheit of cooling with misting systems.
• Between 0% – 40% humidity, you can get up to 30 degrees Fahrenheit of cooling with misting systems.

Read Also: How much do misting systems cool?

Additional benefits of misting

• Cleans the air by getting rid of dust and other contaminants. The water droplets that don’t evaporate faster usually collide with the particles in the air and take them down.
• Reduces odor.
• Keeps flying insects away.

Other factors to consider when getting a humidification misting system

The following factors will also influence the performance of your misting system:

• The dimension of your misting fan relative to the outdoor space.
• The number of fan speeds available to adjust the misting output depending on the humidity levels.
• The height of installation shouldn’t be too high where it doesn’t cool the area well, or too low where the water droplets end up making the place wet.
• Ease of use: In this case, you may look at things like portability. Especially if, you’d change the set-up often.

Conclusion

Now that you how misting systems work in high humidity, you shouldn’t be scared to buy and install them in your outdoor space. Just make sure you get the right one for your needs. In case of any uncertainty consult a qualified technician near you or send us a message in the comment section.

Read Also: List of the best misting system for greenhouse

The post Do misting systems work in high humidity? appeared first on Home Gadgets.

Here are some of the quietest 80-gallon air compressors you should consider.

Top 4 quietest 80-gallon air compressors in 2022

These are the quietest 80-gallon air compressors available in the market right now.

1. Quincy QT-5 Splash Lubricated Reciprocating Air Compressor

If you are looking for efficiency and cutting down operational cost then this top quiet 80-gallon air compressor then this Quincy machine is what you need.

The compressor measures 37*24*74 inches and weighs about 625 pounds. It includes a vertical tank with a working pressure of 145-175 PSI and a 3/4 inch ball valve outlet. Its cast-iron pump runs at 942 RPM.

Pros

• Low operational costs
• Low noise levels
• It is energy efficient
• 50,000+ hours pump life

Cons

• It is expensive to purchase
• It is hard to move around due to its heavyweight

2. EMAX Yellow, Industrial Series, Model ES05V080I1 Compressor

This air compressor from EMAX comes with an efficient dissipation mechanism that makes it one of the quietest 80-gallon air compressors available in the market right now.

It measures 39*32*75 inches, weighs 715 pounds, and can withstand a pressure of up to 12 bar. The motor and pump run at 1750 and 800 RPM respectively.

Pros

• Low noise levels
• It has a durable design and can serve you for longer
• Comes with a 5-year warranty

Cons

• It is expensive to buy
• It is heavy to move around

READ ALSO: The best airless paint sprayers under $500

3. Campbell Hausfeld HS5180

This Campbell Hausfeld air compressor is another good option for small shops and DIY users looking. It comes in a vertical design with 31*41*78 inches dimensions.

The air compressor is ideal for small shops or DIY users. With a working pressure of 90-175 PSI and a weight of about 8 ounces, it is one of the quietest 80-gallon air compressors you can find.

Pros

• Lower weight
• User-friendly design
• It has a fair price tag

Cons

• Shorter pump life of 12,000 hours max
• Slightly loud

4. DeWalt DXCMV5048055

This air compressor from DeWalt measures 31.5*34.7*80 inches and weighs 470 pounds. It features a 5-HP motor and a thermal overload system for protection against voltage fluctuations.

It comes with a conveniently integrated control panel and has a working pressure of 100-175 PSI.

Pros

• Thermal overload protection
• Dual outlets
• User-friendly design

Cons

• Slightly louder
• Draining can be challenging

READ: The best sump-pump float switches that are cost-effective

How many decibels is an air compressor?

When looking to invest in a quiet air compressor, one of the important things to consider is their decibel rating. The rating of most compressors available today is between 40-90 dB. The higher the decibel rating, the louder the compressor is.

Air compressors with a rating of 40 dB are considered low noise. They are usually for domestic use. The 60 dB machines are the mid-rated ones and the amount of noise they emit is tolerable for use in a domestic setup. With 85 dB and above the noise can be very loud, long time exposure to this kind of noise can cause hearing damage unless you use hearing protection.

People often buy compressors with high ratings and it turns out to be intolerable because of the noise. Pay attention to the rating of the air compressor you want to buy, if it is not indicated then it is better you inquire from the manufacturer.

Advantages of an 80-gallon air compressor

In the market, you will find air compressors with different tank capacities. The right capacity to look for in your compressor is mainly determined by what you are going to use it for. However, large-capacity machines like the 80-gallon compressors are proving to be a favorite among many users. They have several advantages over other air compressors.

With the large capacity for air storage, you can use your air compressor for longer hours without it running out. This means fewer interruptions like it would be the case if using an air compressor with less tank capacity.

Also, there are some tools that will only work well if there is a continuous supply of air. This means with a large capacity tank like this, these tools can work optimally. If you don’t have multiple heavy pieces of equipment, check out our cheaper sub $200 compressors or 6-gallon air compressors that are perfect for small-scale DIY use.

Air compressors have become essential machines for our day-to-day lives. From the gas station where they are used to fill car tires and in powering workshop tools like drills and spray guns among other things. With the above buying guide on the quietest 80-gallon air compressor, you can be able to own a machine that meets your needs without having to worry so much about the noise.

The post The 4 quietest 80-gallon air compressors in 2022 appeared first on Home Gadgets.

This is a system designed to emit mists of pressurized water through a special nozzle. You can install it on your patio, gazebo, parks, lounges, and several other outdoor spaces.

We’ll get into detail about how to use the system, its working mechanism, the best way to install it, cost, among other important factors. Keep reading to learn more.

How does the patio misting system help you to cool down?

The same way your body sweats, and you cool off when the sweat evaporates, the patio misting system helps to activate this cooling feeling. How? By releasing water droplets into the hot environment, which then evaporates into the atmosphere causing a drop in temperature in that area. Depending on the effectiveness of your patio misting system, the temperature reduction can be as much as 30 degrees Fahrenheit.

Note: The humidity level impacts the performance of your outdoor misting system. High humidity inhibits the rate of mist evaporation. So, the cooling slows down. The ideal relative humidity levels should be between 40 to 80 percent.

Read Also: The best personal misters for cooling yourself down

The different types of patio misting systems

Patio misters are mainly grouped as per their water pressure mechanism. They include low-pressure, mid-pressure, and high-pressure outdoor misting systems.

• Low-pressure patio misting systems: These are the most affordable and easiest to use out of the three. You simply connect to the home’s main water supply and it’s good to go. Here you’ll be working with a water pressure of about 40 to 60 pounds per square inch (psi). As a result, the mist isn’t as fine as the other two systems. So, the cooling is slower, and you should expect higher residual moisture.
• Mid-pressure patio misting system: For these patio misters, you’ll need a water pump to help boost the water pressure to around 160 psi and 250 psi. The results are; a finer mist, highly effective and rapid cooling of the surrounding, and less residual moisture. They cost more than the low-pressure systems and have an even higher operating cost since the pump uses electricity.
• High-pressure patio misting system: These patio misters use large and powerful pumps to increase the water pressure to a range of between 750 psi and 1,500 psi. You can expect very fine mist and faster cooling from this system. However, these come at a much higher cost. Starting from the purchase of the system, the pumps, and you might require professional help to install. Not to mention the high electricity bill of running the pumps.

How much is a patio misting system?

The average pricing for a low-pressure patio misting system is between $30 and $100.

The mid-pressure system cost ranges from $200 t0 $1,000, while the high-pressure system will set you back between $1,500 and $3,500.

Installing the patio misting system

There are several steps to follow if you want to install the patio misting system properly. They include:

1. Taking measurements

You need to know the actual distance from and between the water source, the power source, and to the end of the setup is. Record the measurements and plan for everything to make your work easy when you start shopping for supplies.

From the tubing, clamps, nozzle heads, line connectors, to electrical wiring for the pump. Also, a drain valve can come in handy if you need to drain out the water in winter.

2. Hang the lines

You can start screwing the lines in place. They have special clips with rubber linings that slide into position once the screws are in. The lines must be at least 8 feet above the ground.

3. Join your pipes

Be sure to use the right compression fittings to avoid any leaks. Especially where the pipes bend to form 90-degree angles. You may need a pair of wrenches to tighten all the fittings securely.

4. Install the pump

First, ensure you get the right pump for your misting system. For instance, for a high-pressure patio mister, you’ll need a pump with an average of 1,000 psi.

If you’re uncertain get an electrician to help you out. They’ll also help you with the wiring and GFCI protection.

Place the pump on a flat surface and protected it from direct sunlight which could overheat the motor. You can then connect the pressure tubing to the misting lines.

Installation to the pump should be firm to avoid movement that results from the vibration of the pump.

5. Turn on the water and switch on the pump

Let the water run through the misting lines to clear air and debris. This also allows you to check for leaks on the tubing and misting lines. Let it flow for 30 seconds to one minute. Once it becomes clear, turn off the water and install the mist nozzles.

You can now start running the patio misting system.

6. Monitoring the patio mister system

To ensure the misting system remains in top shape, you must monitor it regularly. Some of the things to watch out for are:

• The tubing: It could wear out due to the pump vibrations. Look for a superior replacement.
• The filter: Clean or change it often (monthly) to ensure it blocks sediments from entering the tubing.
• The nozzles: Watch out for any irregular sprays. If there are any blockages flush the lines using water mixed with nozzle cleaner.
• The pump: Disconnect and store it properly when the cold season sets in. That’s after you’ve drained it completely. Annual checkups for wear and tear are a must.

For areas with hard water problems, look for water treatment options that you can adapt to your system.

Do patio misters use a lot of water?

The average water use for outdoor misters is between 600ml and 800ml every minute. Fortunately, there are systems that come with the expected water usage in the product description. The two options that you’ll come across are 51.1 LPH (Liters Per Hour) or 13.5 GPH (Gallons Per Hour).

The actual water consumption of your outdoor misting system depends on the following factors:

• Type of nozzle.
• The number of nozzles available.
• Frequency of usage.
• The water pressure.

These variations determine how much water the patio mister uses. For instance, an average nozzle will use between 0.5 gal and 1.5 gal of water hourly. Now, to get the total consumption, you’ll have to factor in each of the other variables.

In some cases, the consumption could be a lot while in others it’s minimal. You can read more about hourly water output from a mister.

Do misters keep flies away?

Yes, flies and other insects like mosquitoes, bees, among others, tend to avoid the mist. This helps to curb any disturbance to the people relaxing on the patio.  Other notable benefits of the patio misting system include:

• Cleaning the air when the mist captures airborne allergens, dust, and other pollutants.
• Watering plants on the patio.
• It’s a cost-effective outdoor cooling system when compared to others like the swamp cooler.
• The low-pressure systems are energy-efficient since they don’t need electricity to run.

Do patio misters work?

As mentioned earlier, patio misting systems can reduce temperatures by as much as 30 degrees Fahrenheit. That shows that they work and are highly effective.

Conclusion

The patio misting system is an innovative way of cooling the temperature outdoors during hot weather. Your only worry is to find the ideal system that falls under your budget, install it right, and maintain it properly.

From our breakdown above, we believe you’ve learned enough about patio misters to use and take care of them appropriately. Don’t allow the summer heat to make your life on the patio unbearable. Install an outdoor mister today and enjoy the cool temperatures.

The post How to use a patio misting system to cool yourself appeared first on Home Gadgets.

The only smoke you have to contend with is a result of fat drippings. Whereas with a charcoal grill you have to deal with charcoal smoke. However, the charcoal barbecue tends to taste much better than a gas grill barbeque combo.

And you know what can make it even better? Using the pellets for smoking meat to fire up your charcoal grill.

And if you think this idea is crazy, think of all the flavor you will be infused into your meat. As the smoke from the wood will emit its natural scent making your meat get an intense flavor profile.

Can you use pellets in a charcoal grill?

Yes. Using wood chips on a charcoal bbq affords you the added benefit of infusing your barbecue with the smoked meat flavor thus making it even tastier.

A key thing to note when selecting the wood pellets is the smoked flavor you would prefer to have in your barbeque. Stick to hardwood pellets as they tend to burn for longer periods of time as compared to softwoods.

There are other valid reasons for using wood pellets, the key among them being recycling which is good for the environment as well as the fact that they are much cheaper than charcoal. It is also less messy than using charcoal.

Read Also: How to keep mice out of your grill

How to use wood pellets in a charcoal grill

1. Get the fire going as you would when you use charcoal
2. Wait until the coal is extremely hot and add the bbq wood pellets
3. You will need to add the pellets every hour or so to keep the fire going

It’s fine to use wood pellets in a charcoal grill. Not only do they cook your barbecue well, but they also add flavor. Besides, they aren’t messy compared to charcoal.

The post How to use wood pellets in charcoal grill appeared first on Home Gadgets.

The cost of the pump is an added expense for users and you may be wondering; do you need a pump for a misting system or your mister will do just fine without it?

To answer this question, it is important you first understand how these misting systems work and the process leading to the cooling mist on the surrounding environment.

Quick answer, If you have low water pressure, you can make do without a pump. If your utility provider delivers low-pressure connections or you get your water from a well without a pressure tank, you will definitely need a pump.

How does a misting system work?

A misting system works by atomizing the water pushed through its lines to form the ultra-small droplets that fill the air. It is these droplets that instantly interact with the surrounding air to absorb the heat and cool it as the water evaporates. To atomize water, it needs to be pressurized and passed through a nozzle which facilitates its dispersion into a spray.

A misting system pump is, therefore, necessary to generate the water pressures required for the atomization process. They come with different pressure ratings, with some below 150PSI, others 300PSI and even 1500PSI for high-pressure systems.

For atomization to occur, you need to use a pump with the right pressure ratings. A 100 PSI, for example, is not adequate for a high-pressure system.

Pro Tip: High water pressure affects the misting system’s flow rate hence how much water it consumes per hour

You also need the right pump for the specific nozzle used in your misting system. Nozzles are normally listed by gallons per hour or gallons per day. The pump you get should provide the adequate pressure and volume required for atomization.

Types of misting systems

Misting systems can be categorized into three main basic types, namely;

• Low-pressure misting systems
• Mid-pressure systems
• High-pressure systems

Whether you are installing an indoor misting system or a patio misting system for your backyard, gazebos or patio, the ideal water pressure for a misting system will depend on your needs. Higher water pressures result in smaller water droplets and faster water evaporation.

High-pressure systems will thus cool the air with almost no wetness, while low-pressure systems cause wetness while cooling. A good example where low-pressure misting systems are used is at the grocery store’s produce section, where the mist needs to be wet to cool and keep the product looking fresh.

If you have low water pressure, you will also be interested in these handheld showerheads designed to work best on low water pressure connections.

Misting pumps come in different shapes and sizes, and you need to get the right one as per your needs. If you do not require lots of pressure, a small misting pump should be able to do the job. A larger pump with higher PSI ratings will, however, be required for high-pressure systems.

The noise level is also an important consideration when buying your misting system pump. For indoor purposes, for instance, you may need a quiet mist pump that makes as minimal noise as possible.

Choosing the right pump for your misting pump can be a headache, especially for those with little information on how these systems work. To avoid overspending on a larger capacity pump you may not require after all, or one that doesn’t generate the right pressure for the system you are running, it is essential you first understand your needs and the type of system you have.

The post Do you need a pump for a misting system? appeared first on Home Gadgets.

Follow these tips to learn how to keep mice out of the grill;

Clean the grill thoroughly before storage

Make sure your grill is always clean. The smell of food or any residue left on the grill after use is the primary attraction for mice.

Scrub down the grills using a safe scraper as well as the rest of the grill to remove any food scent that might attract the mice.

Invest in a rodent-proof grill cover

Get a rat-proof grill cover that will prevent the mice from moving into the grill. Most of these covers are coated in a chemical. It will deter the mice from trying to eat their way through it.

They also tend to be made from a material that is weatherproof and hard for the mice to chew.

Read Also: The best camping grill stove combo

Make it inhabitable

To keep rats from bbq colonization, discourage them from wanting to inhabit the grill by using rodent traps to deter them from staying in your grill.

You can use a mousetrap, sonic pest control, or poison to keep the mice away. You can also use repellents such as cloves, cat fur, peppermint oil, or camphor as mice despise these scents.

Last but not least, buy a well-built grill. There are grills in the market that don’t have any open spaces that small rodents often take advantage of. Which makes them perfect rodent-proof grills. If worse comes to worst, consider hiring an exterminator to get rid of the mice in your compound.

Read Also: Using wood pellets in a charcoal grill

The post How to keep mice out of your grill appeared first on Home Gadgets.

There are a number of factors to consider in order to determine how much water a mister uses per hour. Not all misters are created equal.

The type and purpose of the system

You need to consider the type of misting system you are using. An outdoor or patio misting system is bound to use much more water than a greenhouse misting system.

Due to the fact that an outdoor system is used to cool while the latter is used to keep the plants moist.

Nozzle count and flowrate

Next, you need to consider the misting nozzle flow rate and the number of nozzles. Ideally, the size of the nozzles determines the mist produced and ultimately the cooling effect. This works in tandem with the water pressure.

You can have smaller nozzle diameters and lower water pressure or vice versa. Water pressure plays a huge role in regulating the nozzle flow rate.

Average water consumption

On average, the best misting systems use between 600ml and 800ml of water per minute. You also have the option to choose the water used by your mister when purchasing it.

The two most common options are 13.5 GPH (gallons per hour) or 51.1 LPH (liters per hour).

You can then multiply these figures by the number of misters in your system to determine the total amount of water used.

Consult your manual or mister specs sheet to get your model’s exact water consumption.

How does a water mister work?

Misters spray a fine mist of water through small nozzles in the air that evaporates thus creating an evaporative cooling effect.

Do misting fans get you wet?

No. the water droplets sprayed are too small that they evaporate as soon as they hit the air to create the much enjoyed cooling effect.

Unless you have a malfunctioning mister, you do not need to worry about getting wet.

Read Also: Need temporary tattoos for the summer? Check out Prinker

The post How much water does a mister use per hour? appeared first on Home Gadgets.