If the Beautyrest heated blanket blinks after washing, it means there’s a technical error. You need to check the digital controller for the specific error code to know what the error means. But if your heated blanket keeps blinking even after you’ve identified and tried fixing the particular error, this guide should come in handy.

Reasons why your Beautyrest heated blanket is blinking

There are several reasons why your electric blanket is heating. The good news is that each problem has a specific solution. We shall discuss each of them below.

1. An open circuit

The most common reason why your blanket is blinking is because of an open circuit. Open circuits are common problems in electric blankets, especially when there are damaged internal wires, which happens when you frequently twist the blanket during washing.

A repair technician cannot fix an open circuit. Instead, you must purchase a new electric blanket and discard the damaged one.

2. Check the Beautyrest heated blanket’s temperature

Before you reset the heated blanket, you need to check whether it is working or not. Below are steps on how to check the temperature of your electric blanket:

• Connect the power cord to a power socket and turn on the blanket.
• Regulate the temperature to the maximum level. 
• Give the heating element five minutes to start. Waiting longer than that can damage it.
• Test the blanket’s temperature by placing your palm between the blanket’s fold. You need to reset the electric blanket if the temperature is not increasing.

READ: How to fix a Sunbeam heated blanket that is blinking red

How to reset a Beautyrest electric blanket

Once you have done the above checking procedure, you can reset the Beautyrest electric blanket. The blinking red light may mean that your blanket needs to be reset. Resetting is an easy procedure done by these quick steps:

• Put the electric blanket on your bed.
• Unplug its power cable from the power supply. 
• Next, check that controller is securely connected to the heated blanket’s component. 
• Look for the label located at the bottom of the blanket. Ensure the blanket’s wires are securely connected to the modules next to the label. 
• Slide the power cord under the bed to prevent them from further twisting.
• Plug the blanket’s power cord into the power outlet and turn it on.

3. Damaged fuse

When your Beautyrest heated blanket blinks, it may also mean the fuse is blown. The fuse is placed inside the control box of the blanket. The fuse blows in most cases due to voltage fluctuations that cause overheating. 

If you have blown a fuse, you should immediately replace it with a new one. A blown fuse is not a common issue, so if you see it happening frequently, the problem may be in the circuit connected to it. You should open the control box and replace the old fuse with a new one with the same power and resistance ratings.

4. Power connection issues

Your Beautyrest heated blanket may be blinking red because of a loose connection between the power cable and the blanket’s controllers.

You can solve a Beautyrest electric blanket that is blinking by securing the connection between the power cord and the blanket. You should double-check that all the cables are in good condition before plugging them back into the blanket.

The electric blanket should also have an adequate and steady power supply. It may be blinking red because it has low power. The amount of voltage required to power the electric blanket is 120V. Any voltage supply less than that will not turn on the heating element and the electric blanket.

READ: A review of Polar Seal heated tops

5. Error codes E, E1, E2, E3, and E4

You may have noticed the above error codes in the controller display, and the Beautyrest heated blanket is flashing green. If you have either of the error codes, follow the steps below to clear them from the controller and get the heated blanket working:

• Switch off the controller power switch.
• Next, disconnect the controller power cable from the power socket.
• Check and ensure that the cable from the controllers to the blanket is securely connected to the blanket’s module. 
• Connect the controller’s power cord back to the power outlet. 
• Switch on the power socket and the electric blanket and see whether the error condition is still there.

If the controller still displays the error codes, switch it off, unplug the power cable from the power supply and contact Beautyrest customer support for further assistance.

6. Disconnected throw

Another reason why your Beautyrest heated blanket is blinking red is that the throw is disconnected or broken.

This can also happen even when you have reconnected the power cords. Therefore, you should reconnect the throw to the blanket’s controller before starting the resetting procedure.

7. Dirt and debris in the plug

Your electric blanket is not working because of dirt and debris in its plug. However, it is solvable by removing the plug from the blanket attachment and cleaning it with a dry cloth or cotton buds. Next, reconnect the blanket’s connection to the cable and turn it on. 

It will eventually resume working normally if there are no internal issues. If the problem persists, contact a professional repairer or Beautyrest customer support for further assistance.

In conclusion

Beautyrest electric blanket is a great appliance that comes in handy during chilly and cold seasons. However, it is frustrating when you sleep cold because the blanket is not working and blinking red. Several reasons are behind it, including a faulty thermostat, blown fuse, and power supply issues.

A simple reset can solve the above problems, while others require that you replace the damaged internal component with a new one. If the blinking light continues after resetting the electric blanket, you should call a repairer or Beautyrest customer support to diagnose and fix the problem.

READ: How does heated apparel work?

The post Beautyrest heated blanket is blinking: Troubleshooting guide appeared first on Home Gadgets.

But recently, many users have complained about Mr. Coffee Iced Coffee Maker’s start button not working. This can be quite inconvenient, especially if you are in a hurry.

The good news is that there are a couple of ways you can fix the coffee maker. You just have to understand what causes it not to start. This is where our troubleshooting guide comes into play.

Mr. Coffee Iced Coffee maker won’t start?

When Mr. Coffee Iced coffee maker is not starting or isn’t brewing, check if the cord is plugged correctly, the power switch is not turned on, or the power outlet has an issue. Once you confirm they are okay, apply these troubleshooting tips:

1. Check the power outlet

The start button may be fine, but there is a problem with the power supply. If the power switch is off, ensure it is turned on and has a stable power supply. You can check its power voltage by connecting another electrical device; if it does not turn on, the socket has an issue. Contact your electrician to diagnose the problem and fix it.

Alternatively, you should check the circuit breaker. Ensure that Mr. Coffee’s ON/OFF switch is turned ON and in good condition. You should also check whether the power cords are in good condition and, if not, consult a repair technician to fix it.

READ: Troubleshooting a West Bend coffee maker that is not working

2. No water in the reservoir

Your coffee maker won’t brew because it does not have enough water in the reservoir. The machine will beep but not brew because the water reservoir is empty.

You can check the water level at the gauge before the coffee maker. If there is no or little water, add some more and try to brew your coffee again.

3. Defective thermostat

A faulty thermostat will prevent your coffee maker from brewing. It is firmly sealed with a metal clip and looks like a small white part. To test the condition of the thermostat, you can use a multimeter to test its terminals. 

If you read no continuity on the terminals, the coffee maker’s thermostat is faulty and needs immediate replacement. Contact a professional repair technician to fix it. 

4. Faulty control board 

Your Mr. Coffee Iced coffee maker may be in service for a long time, exposing the control board to wear and tear. As a result, your control board gets damaged and fails to start the coffee machine. 

Fixing a control board is a complex job and not recommended to do on your own. Instead, you should allow a professional technician to replace the control board.

READ: Can I use Verismo pods in a Keurig?

5. Dirty coffee maker

If your coffee maker fails to start, it is clogged with dirt and minerals from your tap water. You, therefore, need to descale the machine to get rid of the mineral deposits. The manufacturers recommend that you descale your coffee maker after 40 to 80 brews.

Below are steps on how to descale your Mr. Coffee Iced coffee maker:

• Pour 4 cups of white vinegar into the water reservoir.
• Place the coffee filter in the brew basket and secure the lid shut.
• Allow three cups of vinegar to flow through the basket and into the mug placed on the cup holder. 
• Turn off your coffee machine.
• Wait for the machine to rest for 30 minutes before turning it on. Then, let the one cup of vinegar flow through the basket and into the mug.
• Pour the vinegar and thoroughly rinse the mug. Remove the filter from the coffee maker’s brew basket.
• Pour one cup of clean water into the reservoir and put a mug under the brew basket. 
• Turn on your coffee maker so the clean water can rinse the residual vinegar in the machine.

You can also clean your coffee machine off the coffee beans residue and mineral build-up. It is recommended that you clean its interior and exterior once a month using the following steps:

• Make a vinegar solution by mixing one cup of distilled white vinegar and one cup of warm water.
• Remove all the detachable parts of the coffee maker and separately wash them.
• If you clean them using soap, ensure that you thoroughly rinse and dry them before reassembling them to the machine.
• Pour the vinegar solution into the coffee’s water reservoir and run a regular brew cycle. 
• Once the brew cycle is complete, run a clean water cycle to rinse the solution.
• Wipe the coffee maker’s exterior with a damp microfiber cloth before brewing a fresh cup of coffee.

6. Wrongly positioned filter 

There is a chance that your Mr. Coffee maker is not working because its filter is wrongly positioned or unbalanced. To fix this, open the lid at the top of the coffee maker and adjust the filter’s position. 

If you have tried the above and the coffee maker fails to start, the filter is faulty and needs immediate replacement. You can find a new filter at a home appliance or hardware store and get a repair technician to replace it. 

Final words 

Mr. Coffee Iced Coffee Maker is a fast and convenient machine that starts your morning with a hot and fresh cup of coffee. However, there are instances where your coffee maker won’t stop blinking or start because of certain technical issues. Most problems are fixable by resetting the coffee machine, cleaning, or descaling it.

Other problems that involve damaged or faulty coffee machine components, such as the thermostat, need to be replaced by a professional repair technician. Finally, remember to maintain and take good care of the coffee made by regularly cleaning and descaling it of dirt and mineral deposits.

READ: How to unclog a Starbucks Verismo machine

The post Fix: Mr. Coffee Iced Coffee Maker’s start button is not working appeared first on Home Gadgets.

Unfortunately, just like most appliances, it’s not immune to malfunctions. Users have complained that their Stanley Fatmax Powerit 1000a turns on itself, doesn’t turn on, keeps beeping, and has many more problems.

The issues are inconveniencing and challenging, especially when they happen unexpectedly and you don’t know the cause of the problem or how to fix it. With the Stanley Fatmax Powerit 1000a troubleshooting tips below, you will not only identify the problems but also fix them.

Common Fatmax Powerit 1000a problems and their fix

These are the most common issues you will experience while using the Powerit 1000a.

The Stanley Fatmax Powerit 1000a won’t turn on

When your Fatmax Powerit 1000a doesn’t turn on, it could be because of issues like dead batteries and lack of charge or complex internal damage to essential components.

To fix this, try the following solutions:

• Check the batteries: Even though it has a huge battery capacity that can’t be depleted easily, you should check to be sure. In fact, to avoid surprises, charge your Fatmax Powerit 1000a at least once per month or whenever the charge runs low. Also, charging helps to maintain the battery life. If the batteries are faulty, you should replace them with new ones immediately.
• Run a power cycle: Power cycling the Fatmax Powerit 1000a helps correct minor system glitches affecting performance. It’s as simple as turning off the device and then waiting a few seconds before switching it back on.
• Turn off the compressor switch: While jump-starting your car or charging other electrical appliances, ensure the compressor switch is off to avoid interference.

READ: How to troubleshoot the Pentair Mastertemp 400

Stanley Fatmax Powerit 1000a keeps beeping

The Stanley Fatmax Powerit 1000a has an in-built safety system that sounds an alarm whenever there’s an incorrect connection. Therefore, to stop the beeping sound from your device, check your clamps connection and correct it.

Also, if you’re running low on oil or used unfiltered or the wrong oil, the Fatmax Powerit 1000a will beep consistently. You’ll have to refill the oil or change it entirely to prevent irreversible damage to parts like the piston, valve, and jack.

Stanley Fatmax Powerit 1000a doesn’t keep charge

If you notice your Fatmax Powerit 1000a drains its battery fast, you may have been leaving it On after use. This forces you to charge it more frequently than necessary. So, to avoid that, ensure it’s switched off after use and stored in a safe place under room temperature.

The LED indicators don’t illuminate

If you pressed the battery status button, but the battery status indication didn’t show, your battery might be completely depleted. You should recharge it, then press and hold the status button again for a few seconds.

The compressor will not inflate

When your compressor fails to inflate, you should try the following:

• Ensure the compressor is turned On.
• Confirm if the Fatmax Powerit 1000a is charged.
• Ensure the nozzle is attached firmly to the tires. If it’s damaged, replace it immediately.
• Press the On/Off button to switch the compressor Off and let it cool for at least 10 minutes, then try to inflate your inflatables.

The USB port doesn’t power the appliance

Check if the USB power button is turned on to troubleshoot USB issues. Next, confirm your Fatmax Powerit 1000a charge. Lastly, check the USB port for damages.

Stanley Fatmax Powerit 1000a is not charging

Charging issues are mainly caused by a faulty charging cord, power outlet, or battery. So, to be sure, try a different cord, connect to another power outlet, or replace the batteries.

READ: The best generator for RV air conditioner

The Fatmax machine starts the stops

When you encounter this problem, you may be using the machine aggressively, running low on water or oil, the valve is damaged, or there’re other internal motor issues. To solve the issue, let the machine rest after continuous usage and don’t overload it. Also, refill the oil and water levels, and replace damaged parts.

Fatmax Powerit 1000a emits cold or hot air

The temperature of the air coming from the compressor should be balanced. Mismatched air temperatures could damage the air calve, air tank, and pipe. The problem is caused by the accumulation of dirt in the compressor, over or under the compressor, and using the compressor for long without a break.

You can avoid these issues when you let the machine rest and check and repair or replace worn-out parts.

Air pressure and flow problems

Low or high air pressure and flow also significantly impact your Fatmax compressor’s performance. The source of the problem could be a faulty piston, valve, gasket, power switch, air filters, fuse, jack, or even power supply.

Check each of them and replace those that are completely worn out. Next, reset the Stanley Fatmax Powerit 1000a and check if the air pressure and flow are balanced.

How long does Stanley Fatmax last?

After the initial charge when you purchase the Stanley Fatmax Powerit 1000a, it can retain the charge for up to 12 months if it’s not in use. However, the charge can only last 1 hour on the highest setting and 7 hours on the lowest setting.

How long does it take to charge a Stanley Fatmax Powerit 1000a?

The time taken to charge your Fatmax to full capacity depends on its discharge level. It’ll need 12-14 hours to recharge if it’s completely discharged. You will know it has finished charging when the LED indicator illuminates, and the green LED light flashes

That wraps up our Stanley Fatmax Powerit 1000a troubleshooting guide. Hopefully, one of the solutions helped you correct a recurring problem, and your machine now works efficiently. You can avoid future problems by simply reading the manufacturer’s user guide and following all the recommendations.

If nothing works, get in touch with the Stanley support team and inform them of your predicament. They’re better placed to understand the problem, diagnose it, and provide the right solution. Also, you should know that they have great warranty policies that will help you save a lot on repair expenses.

READ: How to choose the right cordless screwdriver

The post Stanley Fatmax Powerit 1000a troubleshooting guide appeared first on Home Gadgets.

It can be frustrating trying to identify and troubleshoot malfunctions in your Pentair Mastertemp 400. Therefore, our team has compiled a list of the common problems with the pool heater and how you can troubleshoot them.

Let’s get to it. Starting with the error codes.

The Pentair Mastertemp 400 error codes

Here’s a list of all codes you may encounter while using the Pentair Mastertemp 400.

1. ERR AGS: Automatic Gas Shutoff

When you see the AGS error code, the gas flow has shut off because of a low flow rate or a damaged pressure switch. To troubleshoot, start by checking if the water flow rate meets the minimum requirement for a heater. If it’s below the minimum, service the pump and filter, then confirm the right operation of the Pressure Switch.

Next, confirm the flow rate is okay, and the water temperature is below 104 degrees F. If it’s above, you must replace the thermistor or control board to stop the overheating. Ultimately, you can replace the AGS.

Also, verify the Internal Bypass Valve and the thermal governor are in top shape and that there’s no blockage in the Heat Exchanger.

2. ERR HLS: High Limit Switch

The HLS error code appears when the water flow rate is below the set minimum for a heater and the water temperature goes above 104 degrees F.

The best solutions include; servicing the pump and filter and replacing the thermistor or control board. If you don’t see any change get a new HLS.

3. ERR PS: Pressure Switch

This error code is triggered by an open pressure switch and water overflow. Correct the water flow rate by servicing the pump and filter to fix it. Next, check the wiring and clear any blockage from the pressure tap.

If nothing works, replace the Pressure Switch and adjust it to close while the pump runs and open while it is off.

READ: Proper placement for misting nozzles to cool you off

4. ERR AFS: Air Flow Switch

If the system hasn’t attained perfect airflow after one minute of a startup, the heater turns off automatically, and the AFS error shows up on the display.

To fix, verify that the blower works, then clear any blockage in the blower intake, exhaust, and heat exchanger. Also, the exhaust shouldn’t be too long.

Next, ensure the wiring and connection of pressure taps to AFS is solid and that the connection of vinyl tubing to AFS and blower isn’t punctured, bent, disconnected, or misrouted.

Lastly, check all the blower wiring and correct the faulty ones. From the line voltage between pins 1 and 3 of the blower connector on the ignition, try the wires BM and F1, and connect between 24VAC and IND terminals on the ignition control board.

If the code persists, replace the AFS, blower, or ignition control board.

5. ERR SFS/E05: Stack Flue Sensor

Does the heater run normally after you turn it on, but then the exhaust temperature shoots to 450F- 500F within 3-5 minutes? Does it start after many tries only for the exhaust temperature to stagnate at 250F or below? Or does it not start at all?

These issues trigger the SFS code, and they are caused by an incorrect fuel supply or a faulty thermal regulator.

To solve the problem, ensure the heat exchanger coil has no leaks, soot, liming, or low flow. Next, confirm the thermal regulator is positioned properly. Thirdly, correct the pressure and volume of the fuel supply.

You may disconnect the sensor and inspect its continuity across its terminals. The resistance is supposed to be 3.5-4.0 mega ohms.

Also, inspect the J3 and J6 connections for corrosion or looseness. If the error doesn’t go away after troubleshooting, you should replace the heater membrane pad, heater control board, and the SFS.

You can replace them in succession while checking if the error disappears. Remember to reset the power to the heater after every replacement.

6. ERR IGN: Ignition Control Module

You’ll see this error code when the Ignition control module doesn’t ignite the heater. To fix it, you must ensure the burner is okay.

First, open the burner and remove anything that might be blocking it. Next, confirm that it’s secured with gas and other lines. If the burner has significant damage, replace it with a new one.

7. E01/126: Temperature Sensor is Open

The water temperature sensor is faulty if you see either of the two error codes on your Pentair Mastertemp 400 display. That could be due to damaged wiring or thermostat. Check the two and consider replacing them.

The Pentair Mastertemp 400 pool heater keeps shutting off

When the heater shuts off when you turn it on, and there is no error code to notify you what or where the problem is, you can reset the system so that it starts afresh. Here is how to use the Pentair Mastertemp 400 reset button:

• Open and turn the underside of the control panel board.
• Press the yellow button on the corner.
• Press the temp pad to set the maximum pool temperature.
• Wait for 30 seconds.
• Press the temp pad again and set the max temperature to 1040 F or lower.
• Wait for 30 seconds.
• Power on your heater to see if the problem is gone.

READ: The best dual shower heads to use in your bathroom

The Pentair Master temp 400 burner issues

The burner has a long exhaust vent if it pulsates or surges on the ignition. To solve it, shorten the length of the exhaust vent and the number of elbows.

Other issues with the burner include:

A loud, high-pitched whine

You’ll hear this noise when the flame is too rich. To troubleshoot, start by confirming the pressure tap between the gas valve and blower inlet. The regulator setting should be -0.2” (-0.5cm) wc. Next, get a certified technician to replace the gas orifice.

The flame doesn’t stay lit even though the combustion seems normal

This happens when the flame current isn’t sensed. To fix it, look for a wet or damaged igniter and replace it with a new one. Secondly, ensure the burner flame holder is grounded properly. Lastly, replace the ignition control module.

The flame is fluttery, the burner doesn’t stay lit, and the exhaust has an acid smell

You will encounter these burner problems when the flame is too lean. The best way to troubleshoot is to confirm the gas regulator setting is -0.2” (-0.5cm) wc. Call a qualified technician to replace the gas orifice if it’s not.

The thermistor

When your thermistor has a problem turning on, check the wiring. If the connection is fine, replace the thermistor.

The Pentair Master temp 400 heat exchanger

When you discover boiling in the heat exchanger characterized by “bumping” sounds, there’s likely low water flow to the heater, the thermal governor is stuck closed, or the bypass valve is open. The solutions include servicing the pump and filter, replacing the thermal governor, and servicing the heat exchanger and bypass valve.

Another symptom of a failing heat exchanger is sweating. A faulty thermal governor causes it, and the best solution is to get a new thermal governor.

You should also check the heat exchanger for signs of corrosion. Immediately you notice the parts are corroding, prepare to get another heat exchanger even before the heater starts acting up.

The red diagnostic LED’s on the back of the board are not on

Switch off the power to the heater for a few seconds, then switch it back on. Ensure the temperature is set above the water temperature. Wait for at least a minute to see if the LEDs turn on.

If the LED’s come on but doesn’t stay on, check if the red “SERVICE HEATER LED” is on. If it’s not, confirm the water temperature is set above the water temperature reading. Are the settings okay, but the LEDs won’t turn on, and the heater doesn’t fire, then it is time to replace the control board.

Pentair Mastertemp 400 service heater light is on

When facing this problem, ensure your temperature setting is above the water temperature. Then, turn off the heater power, wait for 5 seconds and turn it back on. If the heater’s power stays on, continue observing its behavior for several minutes to be sure it won’t malfunction again.

Additionally, confirm the burner is firing. If it’s not, verify the status of the blower. In case it’s not responding, replace the control board. But, if the blower is okay, ensure the gas supply and flow are seamless. Don’t hesitate to replace damaged gas valves that are leaking.

The red Service System LED is on

This could be because of filter blockage, minimum water flow, or pump issues. Your first solution is to service the pump and filters and remove any blockage.

Also, adjust the water pressure switch downwards until the service system LED turns off. The minimum flow requirement for the Pentair Mastertemp model 400 is 40gal/min (151 LPM).

The green SPA or Pool LED is off

The absence of these LED lighting means the line voltage to the heater has a problem. To correct it, you must ensure the 12-pin plug is installed correctly (red 240V and clack 120V).

Also, you’ll have to check the wiring connections between the power supply and junction box, the junction box and terminal board, and between the terminal board and transformer primary. Restore continuity wherever there’s a fault.

If the wiring is okay and you still have the problem, replace the transformer.

The gas flows during ignition try, but your burner doesn’t fire

In this case, the problem could be the voltage across igniter leads or the gas pressure. For the former, you must replace the ignition control module to fix the gas pressure. You’ll need a large gas line and replace the meter and/or regulator.

Pentair Mastertemp 400 display is not working

The key factors that can lead to the display failure are a damaged display board and switch. However, other issues like disrupted connection, poor water flow, and faulty ignitor can also trigger or worsen the situation.

To troubleshoot the problem, you can check and replace the display board and the controller fuse, turn off the by-pass valve so that water passes through the heater, repair or replace the ignitor, unplug the heater then plug it back after a few minutes.

Maintenance of your Pentair Mastertemp 400

To avoid troubleshooting the Pentair Mastertemp 400 every time it develops a complication, regular schedule maintenance. This will help identify minor issues before they escalate and stall the heater’s performance. It’s recommended to do the maintenance every 6 months at the start of each swimming season.

Here are some of the factors you should check:

• Test the function of the pressure relief valve.
• Check the heater panels and venting system. Remove any obstructions that prevent ventilating air flow, burner exhaust, or room air.
• Ensure there are no combustible materials, gasoline, or corrosive liquids near the heater.
• Test the water pressure switch.
• Inspect the joints for signs of leakage, check the pipes for cracks or breakage, and ensure the combustion air blower is well-lubricated.
• You can curb corrosion of the heater’s parts by maintaining balanced water chemistry in your pool and installing a corrosion-resistant positive seal check valve between the chlorinator and the heater. Also, test the water regularly and ensure the chlorine residual doesn’t fall below 0.6 ppm.

To ensure the maintenance is done properly, get a professional technician to check the entire system. They’ll know what to look for, where, and how to fix underlying issues.

Conclusion

Hopefully, these troubleshooting solutions will help you to fix your Pentair Mastertemp 400 issues. If there are other underlying issues, share them in the comment section, and we’ll address them.

The post Common problems with Pentair Mastertemp 400 and the fix appeared first on Home Gadgets.

While it is one of the most reliable heated blankets on the market, it is sometimes frustrating when it continuously blinks and you don’t know the problem. 

Not to worry, because this article will explain the common reasons why your Sunbeam heated blanket is blinking.

The most common reasons include a wrongly set thermostat and power supply issues. You will also learn how to fix a Sunbeam electric blanket that is blinking red and get it working normally.

What does it mean when your heated blanket is blinking?

It is common to see your electric blanket blinking on the gradient control. In addition, you may notice an FF sign flashing on the digital control panel. If you see this, the electric blanket has detected a problem and you need to reset it.

Resetting a Sunbeam heated blanket is an easy process. First, you must unplug it from the power source and then plug it back in. Next, ensure that the cord is connected to the module so that the electric blanket resets successfully. 

RELATED: How does heated apparel work?

You can then set the control to ON. If the blinking light persists, disconnect the power cord from the power supply and contact Sunbeam customer support.

Aside from disconnection, the Sunbeam electric blanket blinks after washing because of a problem with the internal heating wires. The heating wires may be damaged when you wash or dry the electric blanket incorrectly.

In this situation, resetting the heated blanket will not work, nor will the blanket heat itself up. You can fix this problem by consulting Sunbeam customer service to diagnose and fix the problem. Furthermore, if the blanket continues blinking after resetting it, you should try other troubleshooting techniques and not ignore it.

Flashing F2

Your Sunbeam electric blanket is blinking the F2 error because it is not receiving enough current. The electric cord may not be secured in the power outlet of the blanket’s module. There may also be a miscommunication between the controller and the blanket that needs to be fixed.

You can troubleshoot this problem by trying to reset the blanket. Unplug it from the wall outlet for a few minutes before plugging it back in. In most cases, this solves the issue. If the heated blanket blinks because of the power supply, fixing the connection or swapping the controllers might solve the problem.

Flashing red light

It means that your blanket is getting no or insufficient power. Alternatively, the power cord may not be connected to the power source or is not secure in the socket. You, therefore, need to check the connection between the power cord and blanket.

RELATED: Should you buy a rechargeable handwarmer?

You can fix the issue by resetting the heated blanket. If resetting does not work, secure the connection between the power cord and blanket. Check for damaged wires which need professional assistance to fix. You will need a new blanket if the damage cannot be repaired.

Flashing E

The flashing error code E means that your blanket is disconnected or its connection is loose. It rarely appears on Sunbeam heated blankets. Reset the blanket if the connections are secure, but the digital control is flashing error code E. Most error codes are cleared off when you reset the blanket.

You should therefore contact Sunbeam customer support for professional assistance. While doing so, check the connection between the power cord and the blanket. If you notice it is loose, push it inside the blanket to make the connection firm. You should check the connection on the power source as well. 

Flashing E2

The flashing E2 error code means the electric blanket’s temperatures are too high. It can also mean a loose connection between the blanket and the control box. The control box may also be disconnected from the wall outlet.

You can troubleshoot the error code by resetting the blanket by simply unplugging and plugging back the power cord to the power outlet. You should also check the plug for recessed pins and fix the loose pins using pliers. Ensure that the loose connections are firm and the plug is not reversed.

Flashing F1

The Sunbeam heated blanket is flashing error code F1 because of a bad connection between the power cord and blanket. A loose connection will make the control panel flash F1 alerting you of a technical issue.

First, you should reset the blanket to turn off the flashing light and clear off the error code. After that, it is simply unplugging the control to the module and plugging it back in. Before you do this, ensure a secure connection between the power cord and power outlet.

RELATED: List of the best vented propane heaters

If your Sunbeam heated blanket continues blinking red even after resetting, consult Sunbeam customer support for professional assistance. They will guide you through the problem and suggest options to fix the heated blanket. Remember to use the repair and replacement warranty if your blanket is too damaged to be repaired.

Other reasons why your electric blanket is not working

A Sunbeam electric blanket may stop working because it is not plugged correctly or its control is not properly set. Your heated blanket may also have damaged cords and internal structures from wear or moisture. Ensure that you take care of the blankets and properly fold them after use to avoid this problem.

The Sunbeam heated blanket may start blinking red when you use it. The digital control also displays error codes that alert the owner when a malfunction occurs.

It may be due to damaged wires, power disconnection, or irregular temperature. You can fix this problem by resetting the electric blanket. The connection between the power cord and the blanket should also be firm and secure. If the Sunbeam heated blanket is still blinking red, consult a professional technician.

The post How to fix a Sunbeam heated blanket that is blinking red appeared first on Home Gadgets.

There are instances where the induction stove will experience issues while using it. An example is when it fails to detect a pan when preparing a meal.

So, why does an induction hob fail to recognize a pan, and what can you do to fix it?

How does an induction cooker detect a pan?

An induction cooktop heats a pan or cooking vessel by magnetic induction. It uses a radio frequency current to a heating coil that generates a strong radio frequency magnetic field.

When you place a pan on the heating coil, the magnetic field emitted from the heating coil creates eddy currents on the pan and hence heats it.

READ: What does error code F31 on a Frigidaire gas range mean?

Will any pan work on an induction hob?

A pan or cooking vessel to work on an induction cooktop should be made of a magnetic material such as iron or steel.

Since an induction hob cooks through magnetic induction, it excites the iron atoms in the cooking vessel. That’s why your pan or pot should be made with enough iron for them to heat.

How do you know if a pan is an induction pan?

You can tell if your pan is an induction pan by placing a magnet at the bottom of the pan and checking whether it is attracted to it. Alternatively, you can check under the pan for an induction logo that looks like a coil. 

It is best to know that just because your pan or pot is magnetic, it does not mean that it can be used on a new glass-ceramic induction hob. Some stainless-steel pans have too much nickel that reacts magnetically but does not work on an induction stove.

How to make a pan work on an induction hob

A pan will work on induction if it is flat, smooth, and magnetic. The best pans to use are those made of stainless steel or iron. If your cookware is not magnetic, don’t worry, the induction converter disk is there to help you.

Induction converter disks are discs made from magnetic materials and placed on the induction stove. Since they gain heat through magnetism, they, in turn, heat the non-induction pans placed on top of them. It is important to note that for the pan to heat evenly, it should have a flat and smooth bottom.

READ: How do I reset my Kitchenaid induction cooktop?

Can you trick an induction cooker?

Yes, you can use an induction adapter plate or induction converter disks for non-induction pans. However, they are recommended if you love and cannot part with the non-induction pan. You should, however, beware of the poor-quality adapter plates that do not work on an induction stove. 

Others say they do not emit enough heat and have low-quality performance. Therefore, you must choose the right converter disk made of high-quality iron or stainless steel.

Another option is using netted steel sheets to heat non-induction pans available in all hardware tool shops. You must double fold the netted steel sheet and place it on the induction cooktop.

Next, place the non-induction cooking vessel on the sheet and switch on the cooktop. It takes longer when you cook with a larger vessel. Take precautions while using this method since you are dealing with hot netted steel.

Do not touch the netted steel when cooking; remove the pan and nested steel after switching off the induction stove.

Cooking with an induction cooktop

The induction cooktop has changed how most people cook in their kitchen households. This is because it uses magnetic induction to heat the cookware. if your induction hob doesn’t recognize a pan, ensure that your pan and pot are made of magnetic materials such as iron or stainless steel.

If your cookware is non-induction, you can use an induction converter disk or netted steel. However, you must note that you purchase a good quality disk so that it heats your pots properly. You should also take precautions when using the netted steel when cooking because it can scald you.

The post Why does my induction hob not recognize a pan? appeared first on Home Gadgets.

So, what does the C-21 error code mean? And how do you clear error codes on a Samsung oven?

What does C-21 mean on a Samsung stove?

The error code C-21 means that the oven is overheating. It shows up on the LED screen when the appliance detects that the temperature is higher than the set temperature.

It occurs due to a few reasons, like a failed Samsung oven temperature sensor, malfunctioning thermostat, or a failed cooling compartment. Alternatively, the relay may be stuck on the board, powering the elements. Note that running an overheated oven for a long time is hazardous. It can ignite and cause a fire.

READ: Troubleshooting an Anova Sous Vide cooker that keeps beeping

If you notice that your oven’s temperature is too high, do not open the door. Instead, you should unplug it from the power source and wait for it to cool down.

An overheating oven can also damage different compartments inside it. The parts that can be damaged include the thermostat, thermal insulation, and light bulb. As a result, the repair costs will be higher than the original.

How to fix the C-21 error code on a Samsung oven

Follow these steps to fix the error code C-21 on a Samsung oven:

1. Restart the oven

Like other electrical appliances, the best solution to an overheating oven is to restart it.

To reset a Samsung oven, switch it off by pressing the OFF button and restarting it. If the error code persists, you can reset it five or six times until it clears off.

If the error code persists, unplug it from the power source and let it rest for at least five minutes. Then, connect it to the power and switch it on. If the error code is still displayed, consult a repair technician or Samsung support to diagnose the problem.

2. Faulty temperature sensor

The main cause of the error code C-21 is a defective temperature sensor. This is a metal probe is located inside the oven, usually adjacent to the broil element. The temperature sensor’s role is to check the oven’s internal temperature and send signals to the main control board.

The control board, in turn, adjusts the temperature to the preferred temperature. Therefore, when the temperature sensor is defective, the oven will fail to regulate its temperature and hence cause overheating.

READ: How to troubleshoot a rice cooker

It may also detect lower temperatures than usual, causing the heating element to stay longer in the oven. This issue can also cause actual overheating and damage to the oven elements.

To solve this, unplug the oven from the power supply and let it cool for a few minutes. Next, use a multimeter to inspect the oven’s temperature sensor. If it is damaged, consult a professional technician to fix it.

3. Damaged cooling fan

The oven has a cooling fan that cools down the oven when it is too hot. A defective cooling fan causes the oven to overheat and displays the error code C-21. You can check whether the fan is properly functioning by running the oven for approximately two minutes.

If the fan does not move, consult a repair technician to fix the problem. Unfortunately, it must be replaced with a new one to resume normal operations. An electric cooling fan can be purchased in any hardware store if you want to fix it yourself.

4. Blocked oven vents

Air vents at the back of the oven regulate air circulation in the electric appliance. The airflow allows the hot air to flow out of the oven and replace it with cool air. When the oven vents are covered with dirt or aluminum foil, it may cause the oven to overheat.

Ensure that the oven is approximately 1.5 meters away from the wall. It would be best if you also cleaned off the dirt and grease in the air vents to ensure proper air circulation.

READ: How to troubleshoot the Ninja Foodi food processor

5. Defective heating element

Your oven may display the error code C-21 because of a failed heating element. Its function is to generate heat that cooks the meals.

A faulty heating element produces more heat than necessary and this causes overheating. You need to use a multimeter device to diagnose the condition of the heating element. If it is damaged, you should immediately replace it with a new one.

6. Defective thermostat

The function of a thermostat in a Samsung oven is to regulate oven temperatures for normal functioning. However, it may be defective because it is worn out or burnt. If so, it needs to be immediately replaced by a repair technician to clear out the error code.

The bottom line

The Samsung double oven error code C-21 means that the oven is overheating and requires special attention. In addition, there may be a problem with the cooling fan, thermostat, or heating element, which all need immediate replacement.

If you have tried all the above fixing techniques, you should consult a professional technician or Samsung customer support to diagnose and fix the problem.

The post How to fix a Samsung oven error code C-21 appeared first on Home Gadgets.

You, therefore, have to reset your electric cooktop on such an occasion. In this guide, we’ll show you how to reset your KitchenAid induction cooktop that is not working.

How to reset a KitchenAid Induction cooktop

To reset a KitchenAid Induction cooktop:

• Leave the cooktop to cool if you have been using it and H is still displaying or flashing
• Turn off the circuit breaker to power off the cooktop.
• Turn on the circuit breaker to power on the cooktop after about a minute

You’ve just reset the cooktop. Verify if it is working.

READ: How to clean stubborn stains on a glass cooktop

Why your induction stove is not working

The induction stove operates on induction or electromagnetism, which enables it to maintain a constant temperature. It also cooks faster than a standard electric or gas-powered heating element.

Errors in the appliance’s settings may prevent an induction cooker from working. There may also be issues with the burner or power connection, which you can inspect and check yourself.

However, if there is a technical issue, you need to consult a professional technician to fix the induction cooktop.

READ: Here’s why your Induction cooker won’t recognize the pan

How to unlock your KitchenAid induction cooktop

The most common reason your KitchenAid induction cooktop is not working is that it is in lock mode. The Lock Mode is a special feature that prevents you from turning on the induction stove through the touch panel.

You can solve this by pressing and holding down the lock button for five seconds until the indicator light turns off. However, if it does not unlock after doing this, there may be a problem with the control panel.

It is a serious problem that should be diagnosed and fixed by a professional technician.

Final words

The most common reasons your induction cooktop is not working is an issue with the power supply or errors on the appliance.

You can solve the problem by resetting the induction stove or oven using the steps above. However, if the problem persists, contact KitchenAid customer service or a professional repairer to troubleshoot and fix your induction stove.

Related: What does C-21 mean on my Samsung oven?

The post How do I reset my KitchenAid induction cooktop? appeared first on Home Gadgets.

It can be stressful when the washing machine stops working and displays an error code like 3C. the first question that comes to mind is, how do I fix error 3C on a washing machine? Read more to learn what this error code means and the troubleshooting tips to clear it off.

What is the error code 3C on a Samsung washing machine?

It means a washing motor or hall sensor error; hence your washing machine is not working. There may also be a floating drain obstacle, or the drain pump has malfunctioned under a laundry load. These are the possible reasons for the error code in the washing machine:

• Faulty washing motor.
• Faulty washing motor hall sensor.
• Incorrect connections of the motor hall sensor connector.
• Faulty washing motor rotor and stator.
• Faulty main PCB.

Below are the troubleshooting tips that may help fix the problem:

1. Reset the washing machine

The washing machine may be experiencing a system glitch. Therefore, it will give false information to the control panel that the machine is a draining issue. To fix this, you can reset the washing machine by turning it off and unplugging it from the power source.

Let it rest for less than five minutes and plug it back into the socket. The error code 3C should have cleared by switching it off, and your washing machine resumes normal operations.

READ: How to clean an iron that has burnt fabric

2. The washing drum is overloaded

Another reason there is a 3C error code on a Samsung washing machine is that it is overloaded with clothes.

You can fix this by removing some clothes from the drum and starting the cycle again. If this method does not work, unplug it from the socket and let it rest for 30 minutes.

3. Power supply issue

The 3C error code tells you that the motor doesn’t have enough power. It then informs the mainboard that it is not spinning as fast as it normally should.

Ensure that you run the machine and check whether enough power is supplied to the drain pump at the drain portion of the cycle.

4. Broken wire

Aside from an overloaded washing drum or system glitch, the wire in the wiring harness may be broken. It results in an intermittent connection to the mainboard and sends no data from the motor. Depending on the model you are using, you can manually fix this problem with the right wiring harness.

5. Faulty washing motor hall sensor

The hall sensor helps the control board ensure there is normal functioning in the washing machine. It is located on the stator at the back of the motor. When it is damaged, it fails to inform the control board that the motor is spinning and, in turn, stops the washing machine.

If this is the case, replace the hall sensor with a new one. You can do it yourself if you know your way around the electricity and its circuits. You will only require the washing machine’s manual, a digital multimeter, and a few tools.

READ: How do heated apparel work?

6. Faulty washing motor

The motor problems may result from worn-out carbon brushes and strange noises. Use a multimeter to test the motor’s continuity and determine its condition by its reading. Set the multimeter to RX1 and test the two probes of the motor.

If it reads 0 or near 0, it is in good condition. However, if it reads infinity, the motor is faulty and needs to be replaced.

7. Faulty main PCB

The printed circuit board or PCB is prone to failure because of burnt components or defects such as misaligned layers, short circuits, and crossed signals. It may trip the electrics and fail to turn on the washing machine when it fails.

If the PCB is tested to be faulty, it should be replaced with a new one. Once you have completed this, restart the washing machine and test whether the error code has cleared.

8. A disconnected motor hall sensor

Because of a foreign object, the washing motor hall sensor may be disconnected from the motor and the control board. As a result, the drum may be jammed and fail to start the cycle.

You can fix this by looking for the foreign object and removing it through the hole of the heating element. To access the heating element, remove the front panel of the dishwasher.

9. Seek further assistance

You have tried all the above solutions, but the error code 3C persists on display. What’s worse is a continuous loud humming sound from the washing machine.

You should consult a professional technician to troubleshoot the problem and fix it. It is preferred that you contact Samsung customer care to diagnose the problem and fix it.

Final words

The Samsung washing machine is a great home appliance that cleans your laundry loads. Therefore, it is stressful when there is a 3C error on a washing machine and it stops working.

The error code means that the washing machine is experiencing a motor or motor hall sensor problem. It can be caused by overloading clothes, faulty motor, hall sensor, or printed circuit board.

You can diagnose and fix the Samsung washing machine 3C error code by using a multimeter and replacement components. If you cannot do it, or the error code persists, consult a professional technician or Samsung customer service to troubleshoot the washing machine’s problem.

The post How do I fix error code 3C on Samsung washing machine? appeared first on Home Gadgets.

There are other issues that may cause the dryer to shut off or fail to work properly. In this article, we’ll explain where the issue arises from and how to troubleshoot it.

What does it mean when your dryer keeps shutting off?

The main reason why your dryer keeps stopping is because of a faulty drive belt. This troubleshooting guide will guide you on how you can fix them:

1. An overheating dryer motor

The main reason why your dryer keeps shutting off after 2 minutes is likely because of an overheating dryer motor. A defective dryer motor causes a continuous buzz sound and must be replaced immediately.

You can also let it cool down for 2-5 minutes before restarting it and if it continues making the buzz sound, replace it using the following steps:

• Unplug the dryer from the power socket.
• Remove the lower access panel and lint filter at the bottom.
• Pull the dryer away from the wall for easy access to the back panel.
• Unscrew the top panel.
• Remove the wires attached to the door switch.
• Finally, remove the dryer’s front panel.
• Using your left hand, grip the idler pulley, push it back and pull the belt off the motor pulley using the other hand.
• Remove the idler pulley from the mounting basket.
• Hold the drum and remove it from the cabinet but leave the belt inside it.
• Locate the wires connecting to the motor and detach them.
• Release the blower wheel and let it rest in the housing.
• Replace the faulty dryer motor with a new one.
• Reassemble all the parts together and check whether the problem is solved.

READ: Fix a Samsung dryer that is running but not heating

2. Overloading the dryer

Overloading your Samsung dryer may lead to it shutting down frequently. Instead of saving time and energy, you damage the dryer pulley and motor. Furthermore, it inhibits the proper circulation of air in the drum.

Ensure that you put the clothes load depending on the dryer’s capacity. The clothes capacity should be less than two-thirds of the clothes tub. You should also put the right amount of water and fabric softener to ensure the dryer runs smoothly.

3. Defective drum belt

The most common reason why the dryer stops working is a faulty drum belt. A drum belt helps the dryer rotate during its cycle. Therefore, it will not work properly if it is defective and requires to be replaced.

Below are the steps on how to check and replace the drum belt:

• Unplug the dryer from the power socket.
• Remove the lower access panel and lint filter from the dryer.
• You will see two screws beneath where the lint filter was. Unscrew them and set them aside.
• Unscrew the screws holding the top panel and set them aside.
• Disconnect the wires connected to the door latch.
• Once the panels have been removed, you will see the drum belt and check its condition.
• If it is not working, replace the faulty drum belt with a new one.
• Reassemble the parts together and check whether the dryer is working normally.

4. Defective door latch

The door latch’s purpose is to close the dryer’s door before starting its operation firmly. Unfortunately, it becomes faulty because of too much use. You can test its condition by closing the door; if it does not close the door tightly, it must be replaced.

Below are the steps to replacing a faulty door latch:

• Disconnect the socket from the power socket or turn off the circuit breaker.
• Remove the door hinges by unscrewing the screws holding them in place.
• Remove the dryer’s door to access and remove the door latch.
• Replace the removed door latch with a new one and replace the door to its original position.
• Reassemble the dryer’s door parts and check whether the dryer runs without stopping.

READ: Whirlpool duet dryer is not spinning but makes a humming sound

5. Defective moisture sensor

A moisture sensor monitors the sensor in the dryer. When there are high moisture levels in the dryer, it alerts the control board to turn off the dryer. However, it will falsely alert the control board that the dryer has no moisture and your clothes are dry when it is faulty. Hence, your dryer shuts itself off.

Here are the steps to replacing a bad moisture sensor:

• Unplug the dryer from the power supply.
• Remove the screws holding the top panel in place.
• Remove the top panel and control panel inside it.
• Unscrew the screws holding the lint screen and close the dryer’s door.
• Look for the locking tab on the front panel and remove it. Detach the front panel and remove the wires connected to the door.
• Remove the control panel and the wires connected to the moisture sensor.
• Separate the mounting plate, lint screen, and grill.
• Remove the old moisture sensor and replace it with a new one.
• Reassemble the dryer’s parts and turn on the dryer to see whether it runs normally.

6. Contact a professional technician

If you have performed all the above troubleshooting methods and your Samsung dryer still turns off after 2 minutes, contact a professional technician to diagnose the problem and fix it. Alternatively, you can also contact Samsung customer service to help fix your dryer under warranty.

Final thoughts

As we’ve explained, there are several reasons why your Samsung dryer keeps shutting off after a few minutes. These include a faulty drum belt, door latch, moisture sensor, and an overheating dryer motor. You can fix most of these problems by yourself using the tools available at home and following the steps outlined above.

The post How to fix a Samsung dryer that keeps shutting off appeared first on Home Gadgets.